ASA DEFAULT PASSWORD FACTORY DEFAULT LICENSE

Configure a static IP address, subnet mask, and default gateway for PC-A, PC-B, and PC-C as shown in the IP Addressing Table.Д«ecause the ASA is the focal point for the network zones, and it has not yet been configured, there will be no connectivity between devices that are connected to it.

Username admin01 algorithm-type scrypt secret cisco12345 Note : R1 does not need any routing as all inbound packets from the ASA will have 209.165.200.226 as the source IP address.Д®nable secret algorithm-type scrypt cisco12345 No additional configuration for R1 will be required for this lab.

Use the following script to configure R1.

Note : To avoid using the switches, use a cross-over cable to connect the end devices Step 2: C onfigure R1 and the end devices. Make sure the router and ASA have been erased and have no startup configuration. Step 1: Cable the network and clear previous device settings.ДЄttach the devices that are shown in the topology diagram and cable as necessary. Note : Do not configure ASA settings at this time. In this part, you will set up the network topology and configure basic settings on the routers, such as interface IP addresses and static routing. пЂЅ Ethernet cables as shown in the topology Instructions Part 1: Configure Basic Device Settings пЂЅ Console cables to configure Cisco networking devices

ASA DEFAULT PASSWORD FACTORY DEFAULT LICENSE

пЂЅ -X (OS version 9.15(1) and ASDM version 7.15(1) and Base license or comparable) пЂЅ 3 PCs (Windows OS with a terminal emulation, such as PuTTY or Tera Term installed) пЂЅ 3 Switches (Cisco 2960+ with Cisco IOS Release 15.2(7) lanbasek9 image or comparable) пЂЅ 1 Router (Cisco 4221 with Cisco XE Release 16.9.6 universal image or comparable with a Security Technology Package license) N ote : Before you begin, en sure that the devices have been erased and have no startup configurations. 15 ( 1 ), Adaptive Security Device Manager (ASDM) version 7. The ASA used with this lab is a Cisco model 5506-X with an 8-port integrated switch, running OS version 9. Refer to the Router Interface Summary T able at the end of the lab for the correct interface identifiers.

Depending on the model and Cisco IOS version, the commands available and the output produced might vary from what is shown in th e labs. Other routers, switches, and Cisco IOS versions can be used. The switches used in the labs are Cisco Catalyst 2960+ with Cisco IOS Release 1 5.2(7) (lanbasek9 image). Note : The router s used with hands-on lab s are Cisco 4221 with Cisco IOS XE Release 1 6.9.6 (universalk9 image). ASDM provides an intuitive, GUI-based tool for configuring the ASA. In Part 3, you will configure additional settings, test connectivity, and configure Adaptive Security Device Manager (ASDM) access.

In Part 2, you will explore two ways to configure basic ASA settings. In Part 1 of this lab, you will configure the topology and non-ASA devices. This lab uses the ASA CLI, which is similar to the IOS CLI, to configure basic device and security settings.

Other devices will receive minimal configuration to support the ASA portion of this lab. The focus of this lab is to configure the ASA as a basic firewall. Inside users can access the DMZ and outside resources. It provides outside users limited access to the DMZ and no access to inside resources. The ASA creates three security interfaces: OUTSIDE, INSIDE, and DMZ.

This lab employs an ASA 550 6-X to create a firewall and protect an internal corporate network from external intruders while allowing internal hosts access to the Internet. The Cisco Adaptive Security Appliance (ASA) is an advanced network security device that integrates a stateful firewall, VPN, and FirePOWER services. Part 3: Configur e Basic ASA Settings and Interface Security Levels Background / Scenario Part 2: Access the ASA Console and Us e CLI Setup Mode to Configure Basic Settings Blank Line вЂ“ no additional information Objectives

Asa default password factory default